The content below about Installing A Bathtub is pretty much engaging. Don't bypass it.
Installing a tub isn't precisely brain surgery, yet it does need solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a moderately difficult task. If the old tub is conveniently easily accessible, the job can relocate immediately; if you have to open up a wall to eliminate the old tub and position the new bathtub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will need an assistant to leave the old bathtub as well as set in the new one. Ensure you have certified on your own for the work and are comfortable attempting it. Instead of hiring a professional to take control of a halfway-completed job, it is much better to take into consideration using one prior to you start. Chances are you may need a professional plumber to make tube connections.
This short article will assist you set up a new tub in your shower room if you have already purchased a new bathtub and also do not require to transform the setup of your previous water pipelines.
Your devices as well as product list must make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you should do is disconnect the water. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be quite bothersome because of the restricted access that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipes. Once the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin making sure that the washers are in place in between the tap as well as the sink. Safeguard the tap in place with the supplier supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The former kind should be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Using the two wooden boards under its feet, position the bath tub in the required setting. The wood boards are practical in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next goal is to guarantee that the tub is leveled all round. This can be attained by examining the level as well as changing the feet on the bath tub till the level reads level.
To install taps, fit the bottom of the furthest versatile faucet port to the proper supply pipeline by making a compression sign up with; then do the same for the other tap.
Switch on the water supply and check all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill up the tub and likewise inspect the overflow outlet and the normal outlet for leakages.
Ultimately, take care of the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub needs to wait up until the tub has been utilized at least once as this will resolve it into its final position.
Preparing for the Installation
To start with, the sustaining framework provided with the bathroom needs to be fitted (if called for) according to the producer's directions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now be ready to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to split a rigid seal, triggering the water to penetrate the wall in between the bath and also the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components and fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked paper or soft rope. Remember to always load the bath tub with water before securing, to permit the motion experienced when the bathtub is in use. The sealant can break rather early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the market. It is a good idea to fit the floor tiles making use of water-resistant or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading about A Step-by-Step Guide to Installing a Bathtub? Post a comment down below. We will be glad to know your opinions about this write-up. In hopes that you come back again soon. For those who liked our page kindly do not forget to share it. Thanks a bunch for your time. Kindly come by our blog back soon.
Additional Information